Difference between revisions of "3D Printed Strobe Ringlight"

From NebarnixWiki
Jump to navigationJump to search
m
(8 intermediate revisions by the same user not shown)
Line 12: Line 12:
 
<br clear="both">
 
<br clear="both">
  
=== Strobes ===
+
== Strobes ==
 
The strobe and capacitor assembly have been harvested from the disposable cameras. The capacitor is glued to the strobe housing with locktite flexible adhesive and the same glue is used to secure the strobes within the structure. Inductors are used to isolate the capacitor/strobes from the power supply to avoid tubes from stealing each other's pulses and exploding.
 
The strobe and capacitor assembly have been harvested from the disposable cameras. The capacitor is glued to the strobe housing with locktite flexible adhesive and the same glue is used to secure the strobes within the structure. Inductors are used to isolate the capacitor/strobes from the power supply to avoid tubes from stealing each other's pulses and exploding.
 
[[Image:Ringflash_Strobe_TubeClose.jpg.JPG|350px|left]]
 
[[Image:Ringflash_Strobe_TubeClose.jpg.JPG|350px|left]]
 
[[Image:Ringflash_Strobe_View1.jpg|350px|left]][[Image:Ringflash_Strobe_View2.jpg|350px|none]]
 
[[Image:Ringflash_Strobe_View1.jpg|350px|left]][[Image:Ringflash_Strobe_View2.jpg|350px|none]]
 
<br clear="both">
 
<br clear="both">
 +
===Brightness Calculation===
 +
Energy in flash
 +
(1/2) * 120e-6 * 330^2 = 6.534 joules
 +
 +
Assume somewhat poor efficiency of 30 Lumens per Joule
 +
6.534 * 30 = 196 Lumens per strobe
 +
x3 strobes = 588 Total Lumens
  
 
= Structure =
 
= Structure =
Line 26: Line 33:
  
 
== Mount ==
 
== Mount ==
Currently the trigger SCR and interfacing PNP transistor are piggybacked onto the stock power supply and trigger board mounted to the topmost strobe. However, the AA battery and holder and currently floating with no home. I would like to design a buck converter to take a lipo down to the required 1.5V or re-design the power converter to run well off of 3.7V as AA batteries are heavy and bulky.
+
Currently the trigger SCR and interfacing PNP transistor are piggybacked onto the stock power supply and trigger board mounted to the topmost strobe. However, the AA battery and holder are currently floating with no home. I would like to design a buck converter to take a lipo down to the required 1.5V or re-design the power converter to run well off of 3.7V as AA batteries are bulky and do not perform well under cold conditions.
 +
 
 +
=Results=
 +
<flickr>13678754815|thumb|left|The light is pretty even for just three lights</flickr><br clear="both">
 +
It's WAY too bright for macro work, though it would work well for classical/portrait photography. At the very least a piece of printer paper has been placed over each strobe to dim it slightly. I really need to add a quench circuit to redirect and interrupt the current path slightly with a programmable (if manual) delay. A 555 pulse generator could work well here.
 +
 
 +
[[Image:DischargeCurrent.png|thumb|left|Discharge current plot for future IGBT control. Looks like the discharge is way too short without an inductor]]
 +
<br clear="both">
 +
 
 +
=Slideshow of Images Taken Using The Ringflash=
 +
<html><EMBED src="http://www.flickr.com/apps/slideshow/show.swf?v=71649" width=800 height=400 type=application/x-shockwave-flash flashvars="offsite=true&amp;lang=en-us&amp;page_show_url=%2Fphotos%2Fnebarnix%2Fshow%2F&amp;page_show_back_url=%2Fphotos%2Fnebarnix%2F&amp;user_id=70259473@N00&amp;tags=ringflash" allowfullscreen="true"></EMBED></html>

Revision as of 21:04, 17 April 2017

Problem Statement

This project is a fork of the previous 3D_printed_LED_Ringflash project. I want actual strobes for when I want crystal clear, bright, short duration burst of light. This is especially useful for deep macro handheld work. I want to use disposable cameras for everything except the camera interface which will require SCRs or transistors.

System Overview

The system consists of a power supply and trigger, a 3D printed mount for the circuitry, a power source, a 3D printed structure to mount the strobes on, and the strobes themselves.

Ringflash Strobe Side.jpg


Power Supply and Trigger

For now these will just be the disposable camera board with the beefiest transformer that I can find. Charge times will be slow because there will be three capacitors instead of just the usual single cap. Triggering will be accomplished by an SCR tied to the PC-Sync output of my camera.

Ringflash Strobe Electronics.jpg


Strobes

The strobe and capacitor assembly have been harvested from the disposable cameras. The capacitor is glued to the strobe housing with locktite flexible adhesive and the same glue is used to secure the strobes within the structure. Inductors are used to isolate the capacitor/strobes from the power supply to avoid tubes from stealing each other's pulses and exploding.

Ringflash Strobe TubeClose.jpg.JPG
Ringflash Strobe View1.jpg
Ringflash Strobe View2.jpg


Brightness Calculation

Energy in flash (1/2) * 120e-6 * 330^2 = 6.534 joules

Assume somewhat poor efficiency of 30 Lumens per Joule 6.534 * 30 = 196 Lumens per strobe x3 strobes = 588 Total Lumens

Structure

Ring

The ring structure was based on the LED version but redesigned to include the proper hole pattern.

Ringflash Strobe Front.jpg
Ringflash Strobe Back.jpg
Ringflash V1 Strobe 3ch 2mm CAD.png


Mount

Currently the trigger SCR and interfacing PNP transistor are piggybacked onto the stock power supply and trigger board mounted to the topmost strobe. However, the AA battery and holder are currently floating with no home. I would like to design a buck converter to take a lipo down to the required 1.5V or re-design the power converter to run well off of 3.7V as AA batteries are bulky and do not perform well under cold conditions.

Results

Ringflash Spider
The light is pretty even for just three lights


It's WAY too bright for macro work, though it would work well for classical/portrait photography. At the very least a piece of printer paper has been placed over each strobe to dim it slightly. I really need to add a quench circuit to redirect and interrupt the current path slightly with a programmable (if manual) delay. A 555 pulse generator could work well here.

Discharge current plot for future IGBT control. Looks like the discharge is way too short without an inductor


Slideshow of Images Taken Using The Ringflash